GO FISHING, use SLABSAUCE Fishing Attractant
Results 1 to 10 of 15

Thread: e32 735i '91 engine starts, sputters, revs up + down between 1000 + 2000 RPM - solved

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Jan 2007
    Location
    Dayton Ohio
    Posts
    1,483

    Default breather valve

    Ok I tested the breather valve, 45.6 ohm so coil is good. A little confused you said "should be closed without power" Without power I can blow in the direction of the arrow only. Should the valve be completely closed in either direction?


    Quote Originally Posted by shogun View Post
    We had that 2 times on an E32 750 Alpina B12.
    First time the ground cable from the engine to chassis was bad. That we replaced and idle was stable.

    Second time the return line from fuel tank = fuel tank breather line and the valve were defective/broken. See here on the B12 http://e32b12.blogspot.jp/ click in the index on idle and scroll far down.
    That is the system on a M30 http://www.realoem.com/bmw/enUS/show...diagId=16_0112
    17 Fuel tank breather valve BOSCH 13901711395
    The tank breather valve should have a resistance of 45 ± 20 Ohm and should be closed without power.

    others:
    idle control valve
    throttle valve
    But as the car has EML, this can be neglected. How about the vacuum hose under the intake? http://i1275.photobucket.com/albums/...psdqxehvrp.jpg
    http://www.bimmernut.com/forum/showt...llo-from-Spain!

    http://www.bimmerforums.com/forum/sh...nifold-gaskets

    http://blog.bavauto.com/8393/bmw-m30...i-635csi-735i/

    Just found a thread on the German forum, there it was the DME http://www.7-forum.com/forum/5/m30b3...-a-167325.html

  2. #2
    Join Date
    Jan 2007
    Location
    Dayton Ohio
    Posts
    1,483

    Default update

    Ok after studying the evap system. I decide to pinch off the hose from the breather valve just before it goes into the intake manifold. Started the car and it rev up and down for about 5 seconds and then stopped. Idle was about 2000 rpm but then again it is like 5 degrees Fahrenheit here. I let it run for about a minute and the idle started to lower itself, but it start reving up and down again. I think I need to reset the computer

    Quote Originally Posted by Kibokojoe View Post
    Ok I tested the breather valve, 45.6 ohm so coil is good. A little confused you said "should be closed without power" Without power I can blow in the direction of the arrow only. Should the valve be completely closed in either direction?

Similar Threads

  1. 1991 e32 735i pan gasket replacement m30 engine
    By Kibokojoe in forum 5 Series BMW
    Replies: 13
    Last Post: 03-24-2021, 12:27 AM
  2. Need an M30 engine for my sons 735i
    By Kibokojoe in forum 5 Series BMW
    Replies: 1
    Last Post: 08-16-2012, 10:27 PM
  3. Stupid engine problem solved...
    By Sidney Rough-Diamond in forum 5 Series BMW
    Replies: 8
    Last Post: 06-03-2007, 12:18 PM
  4. Occasional 525i M50 Engine Misfire Problem – Solved
    By stilljester in forum 5 Series BMW
    Replies: 3
    Last Post: 01-20-2007, 11:11 PM
  5. Couple of related questions on M50 engine revs
    By ktteoh in forum 5 Series BMW
    Replies: 0
    Last Post: 12-06-2005, 06:46 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •