Parting out the Beast: Brembo, Koni, M-Tech, etc....

[Cacatfish]

Hi folks, I am parting out my 1990 525i and these are some of the parts available:

Front Brembo brakes:
332mm vented, drilled rotors with 4 piston fixed calipers. Work perfectly. New: $2k sell: $1k

Vortech V1 supercharger kit for M50/S50 motors:
Everything needed as well as front mount oil cooler and tapped UUC oil filter housing top for return line. Works great. V1 is a whistler and not subtle.
Software is for 3.2 with cams, so you will probably need software for your car. Receipts avilable new for $6300. Sell: $3000

Suspension: Near new front Koni SA's and older rear Billie Sports. Together with with near new Dinan springs and front Kmac camber plates.
Preference will go to the person who will take the units complete.
New prices: ~$1150. Sell: $750 complete or will part if no takers.
25mm/19mm M-tech sway bars. Nearly new. I think I paid around $275 for the set. Sell: $200

Wheels: E39 540i type 32 wheels. 17x9 and 17x8. Very good shape. A little minor rash and a few minor blems, but presentable: $750obo

Rack and pinion steering conversion:
Front crossmember with complete conversion, including tie rods, (1995 VW)rack, custom lower steering shafts, u-joints.

Supersprint cat-back exhaust: Excellent shape. maybe a few dents, I'll have to check, but solid, no rust or anything. Sounds great at WOT! Price:? Not sure, make offer....

Ellipsoid lowbeams with modded 9005 bulbs: $50

3.15 LSD This may be spoken for, but interested to hear what it is worth.

Gauges: full gauge set, including oil temp, oil press, volts, water temp, fuel press. First three are in a panel that fits right below the ashtray. Panel complete with oil temp, press and volts: Not sure, maybe $100 obo.

Motor/tranny/clutch are all spoken for. Any other small parts? Let me know...Car is Bronzit with tan interior. Front seats arent that great, glovebox latch is broken, door panels are a mixed batch. All electronics work.

Just to let everyone know.....first email received does not connote priority. With me it is the first person from whom I receive an acceptable offer for parts. The car will be stripped July 12 in North Bay Area. Local pickup highly encouraged.

I will be out of town until Monday, so I will be slow returning emails before next week.

Thanks, Colin

[525iT_Feen]

Email sent Colin.

[Gooch]

E mails sent to you.

Thanks.

[Mike M]

pm sent

[Hector]

Hi folks, I am parting out my 1990 525i and these are some of the parts available:

Front Brembo brakes:
332mm vented, drilled rotors with 4 piston fixed calipers. Work perfectly. New: $2k sell: $1k

Vortech V1 supercharger kit for M50/S50 motors:
Everything needed as well as front mount oil cooler and tapped UUC oil filter housing top for return line. Works great. V1 is a whistler and not subtle.
Software is for 3.2 with cams, so you will probably need software for your car. Receipts avilable new for $6300. Sell: $3000

Suspension: Near new front Koni SA's and older rear Billie Sports. Together with with near new Dinan springs and front Kmac camber plates.
Preference will go to the person who will take the units complete.
New prices: ~$1150. Sell: $750 complete or will part if no takers.
25mm/19mm M-tech sway bars. Nearly new. I think I paid around $275 for the set. Sell: $200

Wheels: E39 540i type 32 wheels. 17x9 and 17x8. Very good shape. A little minor rash and a few minor blems, but presentable: $750obo

Rack and pinion steering conversion:
Front crossmember with complete conversion, including tie rods, (1995 VW)rack, custom lower steering shafts, u-joints.

Supersprint cat-back exhaust: Excellent shape. maybe a few dents, I'll have to check, but solid, no rust or anything. Sounds great at WOT! Price:? Not sure, make offer....

Ellipsoid lowbeams with modded 9005 bulbs: $50

3.15 LSD This may be spoken for, but interested to hear what it is worth.

Gauges: full gauge set, including oil temp, oil press, volts, water temp, fuel press. First three are in a panel that fits right below the ashtray. Panel complete with oil temp, press and volts: Not sure, maybe $100 obo.

Motor/tranny/clutch are all spoken for. Any other small parts? Let me know...Car is Bronzit with tan interior. Front seats arent that great, glovebox latch is broken, door panels are a mixed batch. All electronics work.

Just to let everyone know.....first email received does not connote priority. With me it is the first person from whom I receive an acceptable offer for parts. The car will be stripped July 12 in North Bay Area. Local pickup highly encouraged.

I will be out of town until Monday, so I will be slow returning emails before next week.

Thanks, Colin

[mike wong]

sent an email

mike

[Cacatfish]

Hi Hector, 25mm is front 19mm is rear. Colin

[Cacatfish]

Update on sold and available parts:
-Ellipsoids are sold
-Main 3 gauges with panel probably sold
-Swaybars probably sold
-Exhaust may be sold if it fits M20 cars....

Most all else still available...
Colin

[Cacatfish]

Oh, also RD front strut bar available NOW: $150obo

[Jazzman]

E-mail on your way ! ! !