GO FISHING, use SLABSAUCE Fishing Attractant
Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Bleeding M50 coolant? No heat.

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Dec 2003
    Location
    PA
    Posts
    5,403

    Default Bleeding M50 coolant? No heat.

    Hey guys - due to my interesting engine layout I have to remove the radiator to get the power steering pump out. So to replace my pump, out came my radiator. Put the radiator back in, power steering is good, rocking. However, I am trying to bleed my coolant system which is the same as stock except with a different fan position, and I am not getting heat in the car.

    The car doesn't seem to over heat or anything, but I am not sure I've got all the air out or whatever. I have no heat in the car which says to me that there is prob air in the heatercore.

    Are M50s in E34s hard to bleed or anything? Maybe my aux pump doesn't work? I don't really care about not having heat, I just want all the air out.

    Thanks guys

  2. #2
    Join Date
    Aug 2008
    Location
    Pennsylvania
    Posts
    206

    Default

    Had the exact same issue. I let the car run for over an hour, no sign of heat. I put a long screw driver to the AUX pump to verify that it works. Since my car wasn't overheating, I took it for a spin. Once the RPM's went up, heat came into the cabin. I had to do this two times before I got all the air out. Give it a try, since you have a manual transmission you can just rev the engine.

  3. #3
    Join Date
    Dec 2003
    Location
    PA
    Posts
    5,403

    Default

    I spent like 10 mins tonight revving it. Nothing. I should just drive it. Meh.

  4. #4
    Join Date
    Aug 2008
    Location
    Pennsylvania
    Posts
    206

    Default

    Did you squeeze the hoses after the valves and for the main feed for the pump? That helped out to my issue. Also, are you getting a steady flow of coolant from the bleed screw? I didn't get any fluid coming out until the air pocket in the heater core was pushed through.

  5. #5
    Join Date
    Dec 2003
    Location
    PA
    Posts
    5,403

    Default

    No not a steady flow of coolant from the bleed screw - in fact, nothing much comes out except steamy air. I didn't mess with it too much. I'll prob tweak around with it tomorrow. I'll squeeze some hoses. I am not even sure my heater valves work.

  6. #6
    Join Date
    Aug 2008
    Location
    Pennsylvania
    Posts
    206

    Default

    You have the same issue I had. The upper and lower rad hoses would get hot, the feed hose for the heater would get hot, but the hoses after the valves were ice cold. You can tap the valves with a screwdriver. I remember reading that if they haven't been used in a while they can become stuck.

  7. #7
    Join Date
    Dec 2003
    Location
    PA
    Posts
    5,403

    Default

    Sweet I'll check it out tomorrow.

  8. #8
    Join Date
    Aug 2008
    Location
    Pennsylvania
    Posts
    206

    Default

    You could also try pressurizing the system by blowing into the radiator. Make sure you don't have coolant everywhere. Trust me on that, coolant doesn't taste good.

  9. #9
    Join Date
    Jan 2004
    Location
    Thunder Bay, Ontario
    Posts
    2,538

    Default

    Jon, do you have the front end lifted? I ask as I've never had an ounce of trouble bleeding the system when I filled it with the front end raised. In fact, I rarely have to do much bleeding at all, just pour a bit more into the resevoir once its running.

    I always do the initial fill through the upper rad hose (end that attaches to the rad) and fill the rad resevoir. Sometimes it'll burp a bit and allow more in.

    Anyhow, just in case it'll help,

    Dave

    10/90 Build 525im, 630,000+km, Eibach/Sachs, Engine Rebuild
    *RIP Oskar the DOG *

  10. #10
    Join Date
    Dec 2003
    Location
    PA
    Posts
    5,403

    Default

    Russia - I only run water - doesn't taste too bad

    Dave - nah no front end lift - I dont like running the engine on jack stands - makes me nervous. But now that I think about it I could idle it on my driveway facing up as seen in my sig

Page 1 of 2 12 LastLast

Similar Threads

  1. Coolant Bleeding Procedure
    By angusbn in forum 5 Series BMW
    Replies: 4
    Last Post: 01-06-2009, 08:59 AM
  2. coolant bleeding m60 engine
    By lvdxd00 in forum 5 Series BMW
    Replies: 7
    Last Post: 10-25-2008, 11:08 AM
  3. M50 Coolant Bleeding from Newbie
    By mrtr10 in forum 5 Series BMW
    Replies: 10
    Last Post: 02-05-2007, 05:34 PM
  4. Bleeding coolant ... and getting wet
    By Jay 535i in forum 5 Series BMW
    Replies: 4
    Last Post: 08-11-2005, 01:22 AM
  5. bleeding coolant sytem
    By foxface in forum 5 Series BMW
    Replies: 1
    Last Post: 06-06-2004, 11:31 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •