GO FISHING, use SLABSAUCE Fishing Attractant
Results 1 to 8 of 8

Thread: Replacing front cross member HELP PLS!

  1. #1
    Join Date
    Mar 2006
    Location
    Auckland, New Zealand
    Posts
    285

    Default Replacing front cross member HELP PLS!

    OK I have finally got the time and the money to fix the bimmer. What's the best way to go about replacing the front cross member? Does it just unbolt and drop out, or do I (shudder) have to disassemble the entire front end?
    Thanks in advance lads and ladies!
    Freude am Fahren - Damn straight!

  2. #2
    Join Date
    Mar 2006
    Location
    East Brunswick, New Jersey
    Posts
    879

    Default

    I did last year for a 86 325es before selling it. Looking at the 5 series again, I think it is an order of magnitude more complicated. No. I've never done it and hope I never have to. Is rust the reason? You need to support the engine. The rest is unbolt and bolt. But it is easier said than done.

    '01 540it, 6/01
    '03 325i 5 speed, 9/02
    '10 535ix. 9/09
    '10 mini 6 speed
    '15 mini countryman 6 speed

  3. #3
    Join Date
    Mar 2006
    Location
    Auckland, New Zealand
    Posts
    285

    Default

    Damaged the front cross member, so it has to be replaced. The damage is too severe to bend it back, but no damage transferred onto the other parts. Has anyone done this on an e34?
    Freude am Fahren - Damn straight!

  4. #4
    Join Date
    Dec 2003
    Location
    baton rouge, loserana
    Posts
    6,922

    Default

    you can ether support the engine on a jack and wood from the bottom or you can hang it from the top by it's front lifting eye with a engine hoist or by running a wood beam (4"X4" outta do nicely, couple small wood blocks under it if it needs to be higher) across from just inside each fender, jack the engine up a few inches and chain it to the beam, that way theres nothing in the way under the car supporting the engine, this would be the ideal time to do a oil pan gasket while the crossmember is off
    all america wants is cold beer warm cat and a place to take a poop with a door on it

  5. #5
    Join Date
    Oct 2005
    Location
    Wichita, KS
    Posts
    139

    Default Frt. X member replacement

    Granted, I've got the 4.0 v-8, but I Carefully removed both crossmembers in the front by using a floor jack and a 2x4 to spread out the load on the oilpan until I was able to put jackstands under the motor mount arms. Installation, including replacement of the motor mounts, was the reverse, with little problem.
    May the Schwarz be with you...

  6. #6
    Join Date
    Oct 2005
    Location
    Wichita, KS
    Posts
    139

    Default Bolt replacement too

    One other thing to mention, mine was a Chicago car - driven daily, year round. I ended up replacing several of the main body to crossmember bolts due to heavy corrosion. They aren't that much money, for the size bolt. Second, if this is the case with yours, I highly recommend pre-soaking the bolts as thoroughly as possible before breaking them loose. The installation torque spec. is not as much as you might think, but you wouldn't know it from how they come out sometimes. Last, consider coating the grip and shank of the bolts in a heavy grease to help keep the elements out of the sleeves they sit in. I used LPS 3 which is an anti-corrosion lube in an aerosol can. We use it on aircraft, and its guaranteed for at least a year of protection. Just spitballing here...
    May the Schwarz be with you...

  7. #7
    Join Date
    Jan 2004
    Location
    Boston, Ma
    Posts
    441

    Default

    The damn parallelogram steering makes it so much harder. I swapped the front crossmember on my e36 in 30 minutes. All you have to do is support the engine, unbolt the motor mounts, lower control arms, and steering rack, unbolt the 4 crossmember bolts, and assemble reverse of installation.

  8. #8
    Join Date
    Mar 2006
    Location
    Auckland, New Zealand
    Posts
    285

    Default

    Sweet. Thanks for the help. Doesn't seem so bad except for the fact that I have to tie up the bloody radiator.
    Freude am Fahren - Damn straight!

Similar Threads

  1. Replacing front crank seal - what else?
    By J.DeFeo in forum 5 Series BMW
    Replies: 2
    Last Post: 06-22-2008, 02:55 PM
  2. Replacing front indicators'
    By montsta56 nz in forum 5 Series BMW
    Replies: 8
    Last Post: 01-09-2007, 10:13 AM
  3. Cross member bar
    By Dan-ny-m398 in forum 5 Series BMW
    Replies: 10
    Last Post: 11-25-2006, 10:41 PM
  4. Replacing front EDC struts
    By cmk in forum 5 Series BMW
    Replies: 9
    Last Post: 05-24-2006, 08:14 PM
  5. FS: 2 front cross-drilled Brembo Cadium Rotors
    By kngpen in forum 5 Series BMW
    Replies: 4
    Last Post: 08-29-2004, 03:47 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •