PDA

View Full Version : troubleshooting the brake system



shogun
08-19-2011, 09:28 PM
Fault
Brakes pull to one side

Cause
a) Tyre pressure incorrect
b) Unevenly worn tire treads
c) Oil on pads/liners
d) Wrong type of pads/liners
e) Dirty floating caliper recesses
f) Guide bolts dirty or damaged
g) Rear wheel alignment adjusted incorrectly
h) Corrosion in floating calipers or wheel cylinders
i) No shock absorber action
k) Pad of one caliper worn
l) Pad glazed

Remedy
a) Correct tire pressure
b) Change or replace tyres
c) Replace brake linings, check for causes
d) Replace brake linings,check for causes
e) Remove and install/clean floating calipers
f) Replace guide bolts
g) Check wheel alignment
h) Remove and install, repair or replace floating calipers or wheel cylinders
i) Check shock absorber, replacing if necessary
k) Replace brake linings , Check floating caliper
l) Replace brake linings , Check floating caliper


Fault
Brakes excessively hot while driving

Cause
a) Vent bore in master cylinder clogged
b) No play between push rod and master cylinder piston
c) Swollen rubber parts due to use of wrong brake fluid
d) Vent bore in expansion tank clogged
e) Corroded floating calipers
f) Cross spring broken
g) Handbrake lever not released fully

Remedy
a) Overhaul master brake cylinder,replacing if necessary
b) Adjust push rod (in older cars)
c) Overhaul master brake cylinder,replacing if necessary
d) Clean expansion tank
e) Remove and install, repair or replace floating calipers
f) Replace cross spring
g) Check handbrake and handbrake cables ,repair if necessary

Fault
Poor braking effect in spite of great force on pedal
Brake-pedal travel normal

Cause
Brake pads oil-splattered or burnt; wrong type of brake pads

Remedy
Replace brake linings

Fault
Poor braking effect in spite of great force on pedal
Brake-pedal travel short

Cause
Brake booster malfunctions - engine vacuum

Remedy
Check brake booster system
- Check engine (valves, cylinder head gasket etc.)

Fault
Poor braking effect in spite of great force on pedal
Brake-pedal travel long

Cause
One brake circuit failed due to leaks or damage

Remedy
Leakage test of brake system

Fault
Brake pedal can be pressed down softly and springily

Cause
a) Air in braking system
b) Insufficient brake fluid in expansion tank - refer to a)
c) Overheated brake fluid - vapour lock due to excessive water content in brake fluid or excessive brake loads

Remedy
a) Top up or change brake fluid
Bleed brakes
b) Top up or change brake fluid
Bleed brakes
c) Top up or change brake fluid
Bleed brakes

Fault
Brake is bled and readjusted, but brake pedal can be pressed down too far

Cause
a) Primary cup in master cylinder damaged
b) Separating cups on floating piston of tandem-brake master cylinder leak
c) Leak in braking system

Remedy
a) Overhaul or replace brake master cylinder
b) Overhaul or replace brake master cylinder
c) Leakage test of brake system

Fault
Uneven pad wear

Cause
a) Wrong type of pads/liners
b) Dirty fist caliper recesses, damaged caps
c) Corrosion in floating calipers or wheel cylinders
d) Swollen rubber ring for piston control

Remedy
a) Replace brake linings
b) Remove and install, repair or replace floating calipers or wheel cylinders
c) Remove and install, repair or replace floating calipers or wheel cylinders
d) Remove and install, repair or replace floating calipers or wheel cylinders

Fault
Brake pads worn at angle

Cause
a) Wheel-bearing play excessive
b) Brake disc not aligned with fist caliper
c) Corrosion in floating calipers or wheel cylinders
d) Angular brake-disc wear
e) Pads worn to less than minimum thickness
f) Spring force insufficient
g) Guide bolts damaged

Remedy
a) Replace wheel bearings
b) Check floating caliper installation
c) Remove and install, repair or replace floating calipers or wheel cylinders
d) Grind or replace brake discs
e) Replace brake linings
f) Replace spring
g) Replace guide bolts

Fault
Seized brake pads, pad does not move off brake disc

Cause
a) Dirty fist caliper recesses, damaged caps
b) Corrosion in floating calipers
c) Vent bore in master cylinder clogged

Remedy
a) Remove and install, repair or replace floating calipers
b) Remove and install, repair or replace floating calipers
c) Overhaul or replace brake master cylinder

Fault
Brakes squeal or rattle

Cause
a) Wrong type of pads/liners
b) Dirty floating caliper recesses
c) Spring force insufficient
d) Brake disc not aligned with fist caliper
e) Brake-disc runout
f) Excessive thickness deviation within braking surface
g) Brake drums eccentric
h) Knocking brake drums
i) Dirt and dust in brake drums
k) Liner wear excessive or one-sided
l) Rust edges on brake discs
m) Pad loose
n) Wheel-bearing play excessive

Remedy
a) Replace brake linings
b) Remove and install/clean floating calipers
c) Replace spring
d) Check floating caliper installation
e) Check brake discs for runout, replacing if necessary
f) Measure brake disc thickness
Grind or replace discs
g) Grind or replace brake drums
h) Grind or replace brake drums
i) Clean and check brake drums
k) Replace brake shoes
l) Grind or replace brake discs
m) Replace brake linings
n) Replace wheel bearings

Fault
Brake-pedal dead travel excessive

Cause
a) Wheel-bearing play excessive
b) Brake disc not aligned with fist caliper
c) Brake-disc runout
d) Excessive thickness deviation within braking surface
e) Brake system leaky
f) Air in braking system
g) Wrong type of pads/liners
h) Automatic slack control of brake shoes does not function

Remedy
a) Replace wheel bearings
b) Check floating caliper installation
c) Check brake discs for runout, replacing if necessary
d) Measure brake disc thickness - Grind or replace discs
e) Leakage test of brake system
f) Bleed brakes
g) Replace brake linings or Replace brake shoes
h) Remove and install brake shoes , repair slack control

Fault
Jammed piston in brake caliper

Cause
a) Dirty fist caliper recesses, damaged caps
b) Brake disc not aligned with fist caliper
c) Corrosion on pistons in floating calipers or wheel cylinders

Remedy
a) Remove and install, repair or replace floating caliper
b) Check floating caliper installation
c) Remove and install, repair or replace floating caliper or wheel cylinder

Fault
Pulsating effect on brake pedal

Cause
) Wheel-bearing play excessive
b) Brake disc not aligned with fist caliper
c) Brake-disc runout
d) Excessive thickness deviation within braking surface

Remedy
a) Replace wheel bearings
b) Check floating caliper installation
c) Replace brake discs
d) Measure brake disc thickness
Grind or replace discs

Fault
Handbrake effect insufficient

Cause
a) Brake shoes oil-splattered
b) Excessive dead travel between brake shoes and brake drums
c) Excessive dead travel in cables
d) Cables adjusted incorrectly
e) Corroded transmitting elements

Remedy
a) Replace brake linings, determine cause
b) Adjusting handbrake
c) Adjusting handbrake
d) Adjusting handbrake
e) Remove and install handbrake and expander locks
Check Bowden cables, replacing if necessary

source: BMW TIS Online Repair Manuals (http://tis.spaghetticoder.org/)