PDA

View Full Version : Camshaft position sensor issue



ktteoh
06-11-2010, 08:55 AM
what symptoms would point towards a faulty camshaft position sensor?

i'm suspecting this but i don't have computer to verify - all i have is engine is running rich on all 6 cylinder - all 6 plugs sooty [never before], idle erratic and hesistancy to rev beyond 2000rpm. also after revving, idle will drop below 500rpm before slowly recovering..ICV is new.

i know with a faulty crankshaft sensor, the engine won't start.

Tiger
06-11-2010, 09:13 AM
Faulty crankshaft sensor does wierd things... not just no-start. On BMW's crankshaft position sensors are the first to go and cause all kinds of erratic problems. Aftermarket dot type... you see a dot on the bottom... is junk.

ktteoh
06-11-2010, 01:45 PM
i'm referring to camshaft sensor.

Tiger
06-11-2010, 02:02 PM
and I am referring to your last sentence in original post.

Dave M
06-11-2010, 05:44 PM
You should have difficulty (or no chance) starting with a failed camshaft sensor.

Dave

shogun
06-12-2010, 03:50 AM
Camshaft Position Sensor Failure Symptoms
FAILURE SYMPTOMS: No start, hesitation, misfire.
While rare, failure of the camshaft position sensor can cause a variety of problems, ranging from a no-spark situation to performance issues. These sensors are devices that contain moving parts and, as such, are liable to fail, although the majority of cars that have them will not see such a failure during the lifetime of the vehicle.

Facts
•Camshaft position sensors rely on a toothed or slotted wheel attached to the camshaft to determine what position of the camshaft (and, by extension, the positions of the pistons) at any time during the operation of the engine. The toothed wheel relies on the Hall effect (a phenomenon in which an electric current is altered when a magnetic field is brought in proximity of a special semiconductor chip), which produces a digital signal when the teeth pass by the other part of the sensor. Another type of camshaft position sensor shines and receives light from an LED through slots on a wheel that is attached to the camshaft.
Function
•The camshaft position sensor sends a signal to the ignition module or the electronic control module (whichever computer is responsible for telling the coils when to fire). This signal carries information on where the camshaft is (and, thus, where each piston is). The information is critical, because an engine can only run properly if the spark plugs fire near the top of the compression stroke, and the computer would be unable to adjust the ignition timing to compensate for driving conditions without that information.
Symptoms
•A failed camshaft position sensor will show up in a number of ways. The worst-case scenario is that there is no spark in the combustion chamber. Other symptoms can include excessively long cranking time when starting cold, rough running on an intermittent basis, poor idle, stumbling or hesitation, a drop in mileage and stalling upon acceleration. These symptoms may also be caused by a failure in the wiring of the sensor.

Significance
•Most modern ignition systems are made without a distributor, and some of these use the signal from the camshaft position sensor to control the ignition timing. Without a properly functioning camshaft position sensor, the engine will be unable to run efficiently---even if the engine is designed to run using the signal from the crankshaft position sensor as a substitute.
Benefits
•An ignition system based on a camshaft position sensor allows the engine to run without having a distributor, and that means fewer moving parts to break down, as well as no need for the traditional maintenance of replacing the points or the rotor

http://www.ehow.com/about_5903731_camshaft-position-sensor-failure-symptoms.html

BE CAREFUL WITH COMPUTER CODES: THEY CAN MISLEAD YOU !
for example if your car smokes black, smells like gas, and barely runs,the computer gives a "rich oxygen sensor" trouble code. The Oxygen sensor is replaced. The car still smokes black, still has a "rich oxygen sensor" trouble code. The codes said the Oxygen Sensor reads rich. This just confirms what any good mechanic could tell by smelling the exhaust: it's running rich! The car really needs a temperature, MAP, or Mass Airflow sensor , or fuel injection service.
LIMP HOME MODE: When the computer decides enough sensor inputs are out of proper range, it will go to a "limp home mode". This mode has effects from almost unnoticeable to fairly radical, depending on what car you have. The mild case is a MIL light and bad gas mileage. Some cars (with computer shifted transmissions) will stay in second gear when in limp home mode! In limp home mode, the computer uses assumed values to control fuel and spark rather than measured (and constantly adjusted) values. This results in poor fuel economy and bad driveability.
http://www.econofix.com/computer.html