GO FISHING, use SLABSAUCE Fishing Attractant
Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: How do you check brake calipers

  1. #1
    Join Date
    Jan 2007
    Location
    Dayton Ohio
    Posts
    1,483

    Default How do you check brake calipers

    Need to know how to check brake calipers. Lost a rotor last night to a new set of semi metalic pads. Pads were installed on Sunday and the rotor and the exterior pad on the left side of the car are destroyed with less than 2 hours of driving. My thoughts are caliper piston could be sticking or that the caliper is not sliding on the pins. How do you check both of these for proper operation?

  2. #2
    Join Date
    Mar 2006
    Location
    East Brunswick, New Jersey
    Posts
    879

    Default

    A C-clamp.
    '01 540it, 6/01
    '03 325i 5 speed, 9/02
    '10 535ix. 9/09
    '10 mini 6 speed
    '15 mini countryman 6 speed

  3. #3
    Join Date
    Jan 2007
    Location
    Dayton Ohio
    Posts
    1,483

    Default

    I think I may have found my problem. I normally hi-temp grease the caliper pins but looking on this forum I have discovered they should be installed dry, or at least using a specialized coating. I bet the grease has caused the pads to bind up. I will pull the brakes tonight and do a through cleaning. New rotors and pads with a clean caliper should do the trick. I will look into the pin lube though

  4. #4
    Join Date
    Feb 2006
    Location
    Oldham, England
    Posts
    3,078

    Default

    Quote Originally Posted by Kibokojoe View Post
    Need to know how to check brake calipers. Lost a rotor last night to a new set of semi metalic pads. Pads were installed on Sunday and the rotor and the exterior pad on the left side of the car are destroyed with less than 2 hours of driving. My thoughts are caliper piston could be sticking or that the caliper is not sliding on the pins. How do you check both of these for proper operation?
    With no pads in, you should be able to move the caliper on the pins by hand. The piston can go in crooked and jam and I use a G clamp push it in. I'd leave a small gap between the clamp and the piston and press the pedal. Then check to see if I could back the piston in again easily. If thats ok, I'd chuck the old pads in and stand on the brakes to see if I could make it jam-no point messing up a new set unless you are happy. HTH

  5. #5
    Join Date
    Jan 2007
    Location
    Dayton Ohio
    Posts
    1,483

    Default

    Will give it a go. Parts are suppose to be in this afternoon

  6. #6
    Join Date
    Jan 2004
    Posts
    4,150

    Default Nope, that wasn't your problem

    even though you're supposed to put them in dry and clean a number of people here have greased them in the past without the problem that you had

    Even with a sticking caliper i haven't seen one kill the pad in only a couple of hours, it usually takes weeks and is pretty obvious by the pull on the steering wheel



    Quote Originally Posted by Kibokojoe View Post
    I think I may have found my problem. I normally hi-temp grease the caliper pins but looking on this forum I have discovered they should be installed dry, or at least using a specialized coating. I bet the grease has caused the pads to bind up. I will pull the brakes tonight and do a through cleaning. New rotors and pads with a clean caliper should do the trick. I will look into the pin lube though


  7. #7
    Join Date
    Dec 2003
    Location
    Eastern Tennessee USi
    Posts
    14,843

    Default

    Back looking at this stuff for todays issues. Amazing info.
    95 E34 530I V2.37
    ===========
    Those who make peaceful revolution impossible will make violent revolution inevitable.

    John F. Kennedy

  8. #8
    Join Date
    May 2004
    Location
    Japan
    Posts
    9,268

    Default

    we had some cases especially on E32 750 with the H31 brake unit in our warehouse which were long time parked, that the brake calipers were stuck. The problem is the brake master cylinder, inside there are some seals and a bakelite ring, this bakelite ring 'swells' by age and then the master is stuck at some point. I know of some people which has disassembled the brake master and 'polished' a bit off the diameter of the bakelite ring.
    Here a pic how it looks inside a H31 brake master cylinder, probably the others look same / similar
    Attached Images Attached Images  

  9. #9
    Join Date
    Dec 2004
    Location
    Sydney, Australia
    Posts
    4,374

    Default

    Quote Originally Posted by shogun View Post
    we had some cases especially on E32 750 with the H31 brake unit in our warehouse which were long time parked, that the brake calipers were stuck. The problem is the brake master cylinder, inside there are some seals and a bakelite ring, this bakelite ring 'swells' by age and then the master is stuck at some point. I know of some people which has disassembled the brake master and 'polished' a bit off the diameter of the bakelite ring.
    Here a pic how it looks inside a H31 brake master cylinder, probably the others look same / similar
    Amazing. What a find. I guess if you strip the master cylinder down and the ring is binding... its staring you in the face. eek! Can it be that the wrong fluid was used?
    Last edited by genphreak; 10-16-2019 at 06:44 PM.

    Join the Aussie
    540i LE yahoo forum

    08/88 535i e34 M30+miller MAF, 'stiens, tints & teeth!

  10. #10
    Join Date
    Dec 2004
    Location
    Sydney, Australia
    Posts
    4,374

    Default

    kibokojoe, re the binding caliper, I doubt the grease is the culprit*, IMHO it isn't used because the grease only attracts dirt which will cause abrasion, even allow larger things to stick potentially (?)

    * unless you hit some sand/fine debris which somehow got lodged in a piston caliper and caused it to bind. Never seen this happen.

    Join the Aussie
    540i LE yahoo forum

    08/88 535i e34 M30+miller MAF, 'stiens, tints & teeth!

Page 1 of 2 12 LastLast

Similar Threads

  1. Replies: 4
    Last Post: 12-31-2008, 10:41 AM
  2. Brake Linings Check Control
    By BFEINZIMER in forum 5 Series BMW
    Replies: 7
    Last Post: 10-21-2007, 01:10 AM
  3. ATE caliper kit for big brake calipers
    By genphreak in forum 5 Series BMW
    Replies: 1
    Last Post: 12-22-2006, 02:52 PM
  4. Replies: 7
    Last Post: 07-02-2004, 11:45 PM
  5. WTB M5 540 740 E32 rear brake calipers/carriers
    By mholbrook in forum 5 Series BMW
    Replies: 0
    Last Post: 05-25-2004, 11:35 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •