Results 1 to 7 of 7

Thread: Fixed my 'Sword' fan speed controller

  1. #1
    Join Date
    Jun 2004
    Location
    Melbourne, Australia
    Posts
    1,305

    Default Fixed my 'Sword' fan speed controller

    Well after several weeks of having nothing but maximum blower speed available I decided it was time to investigate one of the common quirks of the E34/E32 series... the 'Sword' module. As the fans variable speed control would work very occasionally (even if only for a few seconds) I realised that it wasn't a case of blown Mosfet transistors but most likely a suspect solder joint, probably where the connector socket joins the PCB. Well a crook joint it turned out to be, but not the connector. It was a capacitor as marked.

    It took a while to trace. I removed the sword module from the climate control box, but left it plugged in. By setting the fan controller about midway and flexing the PCB I could cause the fan to cut in and out. After re-soldering the connector joints I retested it but no joy. Still the same. Finally I pushed a prodded each component on the PCB until I narrowed it down to the said capacitor. The slightest touch to this triggered the intermittant operation. I resoldered the capacitor and VOILA! Sword fixed!!

    Last edited by pundit; 02-12-2005 at 05:17 AM.

    1990 E34 535iA, 215,000kms (130,000 miles).
    Dual Climate, Rear Headrests, Rollerblind, M-Tech Wheel,
    Memory Seats, EAT Chip, T-Stars.

  2. #2
    Join Date
    Dec 2003
    Location
    Sydney, Australia
    Posts
    308

    Default Great find, Pundit...

    ...I've never seen that fix before. Another one for the archives.

    regards
    Phil

  3. #3
    Join Date
    Jan 2004
    Location
    Albuquerque, NM
    Posts
    953

    Default Thanks!

    Great sleuthing, thanks for posting it. I have a few more pic's on page 1 of the bimmer.info 7 forum. Similar re-flow-the-solder-fix solved my intermittent blower motor.
    gale
    92 735i 5-spd, turbo project finally underway!


  4. #4
    Join Date
    Jun 2005
    Location
    New York City
    Posts
    48

    Default

    Anyone on this thread know what years the "sword" can be found on (as opposed to box-shaped resistor)? Thanks

  5. #5
    Join Date
    Apr 2004
    Posts
    517

    Default

    '89-'90 certain. May have been phased to new style in '91.

  6. #6

    Default

    Hi
    My car is an E34 525i of year 1990 (july). I had "the" sword problem as a lot...
    The old BUZ71 were out of order and I changed them with BUK9518 that are damn much better (Rdson only 0.018 ohm instead of 0.1 ohm). The result is perfect with
    no longer overheating problem.
    The sword was mounted at that time on cars with automatic A/C system.

  7. #7
    Join Date
    Mar 2005
    Location
    Long Beach, CA
    Posts
    2,563

    Default

    Well Done!

    Ralph Mendoza Jr. - Long Beach, CA

Similar Threads

  1. AirCon controller exchangeability
    By Bo525i in forum 5 Series BMW
    Replies: 5
    Last Post: 04-10-2008, 01:45 PM
  2. Replies: 0
    Last Post: 11-16-2005, 03:52 PM
  3. Control Check fixed/not fixed??
    By Ian Dodd in forum 5 Series BMW
    Replies: 7
    Last Post: 03-29-2005, 04:33 PM
  4. Traffic Signal Controller?
    By Incantation in forum 5 Series BMW
    Replies: 1
    Last Post: 11-17-2004, 01:27 AM
  5. Replies: 3
    Last Post: 06-30-2004, 04:40 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •