GO FISHING, use SLABSAUCE Fishing Attractant
Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: E28 Wont Start - No Spark

  1. #1
    Join Date
    Jan 2004
    Location
    Northern, NJ
    Posts
    119

    Default E28 Wont Start - No Spark

    My friends 535i (e28) won't start.

    (1) Car cranks over fine. Plenty of juice in battery.
    (2) Fuel pump is working and engine is getting fuel.
    (3) Airflow meter is working.

    I removed spark plug and plug does "not" fire.

    (4) I am guessing cap and rotor as next to look at.

    Can anyone help?

  2. #2
    Join Date
    Feb 2004
    Location
    Homestead Florida
    Posts
    78

    Default

    i would chech the pick up sensor

  3. #3
    Join Date
    Dec 2003
    Location
    Toronto, CANADA
    Posts
    882

    Default

    A few years ago I posted a fix for this on a few boards. (when the problem is cold solder joints on the leads to the ignition coil driver transistor). Someone made a detailed repair guide from the info, which you can find here:

    http://members.roadfly.com/louielouie/dme_fix.html

    Even on DME's which are working, you will almost always find the connections to the ignition coil transistor are failing. Two people came over last week with E28's (for chips) and they both had the problem, but not yet to the point that they noticed more than a rough idle.

    Mark

  4. #4
    Join Date
    Jan 2004
    Location
    Northern, NJ
    Posts
    119

    Default

    Thank you, I have a running E28 same year.
    What is procedure for swapping out the ECU.

  5. #5
    Join Date
    Jan 2004
    Location
    Northern, NJ
    Posts
    119

    Default E28 Won't start No Spark - Need Help !!

    The car is a 1988 535is

    I have a running 1988 535i so I have parts that I can swap.

    Here is a list of the parts that I have confirmed to be ok:

    1) Replaced Bosche Cap and Rotor with new from BMA.

    2) Swapped Coil and Motronic.

    Car still wont start.

    I have removed the Crank Positon Sensor but I am not sure if this
    is going to solve this issue.

    The car has plenty of cranking power and the fuel pump is working.

    Is it possible the coil is not getting 12 volts from the battery?

    Any help would be great.

  6. #6
    Join Date
    Jan 2004
    Posts
    1,171

    Default

    Mark...have you seen similar solder failures on '89-92 E-34/E-32 big six DME's as well?
    Thanks,
    George

  7. #7
    Join Date
    Jan 2004
    Location
    Northern, NJ
    Posts
    119

    Default MRBMW1 Did you mean the "Reference Sensor" ??

    This 535is has a "Crank Position Sensor" which is in the front of the engine that has three wires to the diagnostic port. It also has a sensor near the back of the engine. See attached picture.
    Attached Images Attached Images  

  8. #8
    Join Date
    Dec 2003
    Location
    Lincoln, NE
    Posts
    559

    Default

    I'm curious if this solder issue would effect an earlier 533i E28. Does the DME for those earlier cars run the coil the same way?

  9. #9
    Join Date
    May 2004
    Location
    Melbourne (Australia)
    Posts
    61

    Default Sounds silly but...

    Hi, I know this sounds a little off beat, but I have had a battery create this kind of problem in the past in a Japanese car I had 20 years ago.

    Good cranking speed, but no spark or hint of ignition.

    Charge the battery for 15 minutes and away it went. Had a discharge test done on the battery and found the current flowed ok but the voltage was below par.

    Replaced the battery and all was ok.

    just a thought.
    Reid (530iA)


  10. #10
    Join Date
    Jan 2004
    Location
    Northern, NJ
    Posts
    119

    Default

    Quote Originally Posted by Reidal
    Hi, I know this sounds a little off beat, but I have had a battery create this kind of problem in the past in a Japanese car I had 20 years ago.

    Good cranking speed, but no spark or hint of ignition.

    Charge the battery for 15 minutes and away it went. Had a discharge test done on the battery and found the current flowed ok but the voltage was below par.

    Replaced the battery and all was ok.
    just a thought.
    Thanks for the idea. I did check voltage to the coil and it was ok.

Page 1 of 2 12 LastLast

Similar Threads

  1. Help - E34 wont start
    By kwbimmer in forum 5 Series BMW
    Replies: 11
    Last Post: 03-20-2007, 04:32 PM
  2. Help!!!! Car wont start!!!
    By GoldenOne in forum 5 Series BMW
    Replies: 3
    Last Post: 09-24-2006, 09:08 AM
  3. car wont start...
    By pong in forum 5 Series BMW
    Replies: 4
    Last Post: 09-16-2006, 03:59 AM
  4. Car wont start
    By 1991 525i Novs in forum 5 Series BMW
    Replies: 4
    Last Post: 06-16-2006, 04:16 PM
  5. wont start- spark plug mangled!
    By bigblue in forum 5 Series BMW
    Replies: 11
    Last Post: 09-27-2004, 09:40 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •