I thought they were all the same part number- except for M5? Even then, the arms I think are the same, just the hubs (to give a slghtly narrower track for 9" rims)- and bushes (offset) are different.
Hello. I am looking to verify that both traiing arms are correct on my car. Looking to get a clue as to the location of the part number on the trailing arm. Seen some numbers by the inner bushing right on the elbow - do not seem to be the part numbers, given the understanding that those start with "333" per realoem.com...
Can someone help?
Thank you.
deleted air conditioning
I thought they were all the same part number- except for M5? Even then, the arms I think are the same, just the hubs (to give a slghtly narrower track for 9" rims)- and bushes (offset) are different.
Join the Aussie 540i LE yahoo forum
08/88 535i e34 M30+miller MAF, 'stiens, tints & teeth!
I thought they also compensated for the angle of the wheel when lowered?
95 E34 530I V2.37
===========
Those who make peaceful revolution impossible will make violent revolution inevitable.
John F. Kennedy
I think only the offest bushes are required to do this Jeff. But I don't know for sure.
Join the Aussie 540i LE yahoo forum
08/88 535i e34 M30+miller MAF, 'stiens, tints & teeth!
I don't think they used the offset bushings on the M5 factory. There is something very special about them arms but I don't remember anyone actually comparing the stock vs M5. I do remember once upon a time that I was on a quest for them things but I never did find any. The thought being that they would solve the crooked wheel syndrome on lowered.
95 E34 530I V2.37
===========
Those who make peaceful revolution impossible will make violent revolution inevitable.
John F. Kennedy
No. Description Supplement Qty From Up To Part Number Price Notes
01 Trailing arm, left 1 33321132329 $842.06
01 Trailing arm, right 1 33321132330 $842.06
02 SET RUBBER MOUNTING ECCENTRIC D=44MM 1 33329058824 $76.91
02 SET RUBBER MOUNTING D=44MM 1 33329061946 $76.9
No. Description Supplement Qty From Up To Part Number Price Notes
01 Trailing arm, left 1 33321137837 $1,265.52
01 Trailing arm, right 1 33321137838 $1,265.52
02 ROTARY SLIDE BEARING 4 33321135808 $114.21
03 Hex bolt M12X1.5X90 2 07119914667 $1.78
03 ECCENTRIC BOLT M12X1,5X97 2 33312226445 $9.42
04 ECCENTRIC FLAT WASHER 2 33312226446 $1.08
No. Description Supplement Qty From Up To Part Number Price Notes
01 Trailing arm, left 1 33321137837 $1,265.52
01 Trailing arm, right 1 33321137838 $1,265.52
02 ROTARY SLIDE BEARING 4 33321135808 $114.21
03 Hex bolt M12X1.5X90 2 07119914667 $1.78
03 ECCENTRIC BOLT M12X1,5X97 2 33312226445 $9.42
04 ECCENTRIC FLAT WASHER 2 33312226446 $1.08
respective part numbers for 525 3.6 m5 and 3.8 m5 (all rhd euro)
Gone but not forgotten
Thanks Paul- and Happy New year!
I don't see how realoem proves it. The arms come with the bushes pressed in to suit the model. They are shown seperately on the diagram I know, but am sure that is how they sell the arms...
Join the Aussie 540i LE yahoo forum
08/88 535i e34 M30+miller MAF, 'stiens, tints & teeth!
the arms dont seem to be different but you see the m5 has a different "bushing",a "rotary slide bearing" whereas on a normal e34 you seem to have the choice of an eccentric or(non?) eccentric 44mm bushing or is the outer one concentric and the inner eccentric(or visa versa?)
Last edited by Paul in NZ; 12-31-2010 at 05:43 PM.
Gone but not forgotten
So M5 has a solid bearing? First I knew... hmm
Or does slide mean something else... M5 have different wheel offset- I thought this was due to different drive flange (hubs). Also, different brakes and a subframe that accomodates the (again different) large case diff and shaft hardware...
Bah, I wish we could compare all the parts.
Join the Aussie 540i LE yahoo forum
08/88 535i e34 M30+miller MAF, 'stiens, tints & teeth!