Results 1 to 3 of 3

Thread: R & R'd the a/c compressor clutch this afternoon . . .

  1. #1
    Join Date
    Jan 2004
    Location
    Albuquerque, NM
    Posts
    953

    Default R & R'd the a/c compressor clutch this afternoon . . .

    The a/c clutch was screaching badly whenever it would engage above 2000 rpm. The gap was way over 0.080" where it's supposed to be 0.013-0.020". It's a Seiko-Seiki rotary R-12 compressor & from what I gather, most BMW compressors are either Bosch or Nippon Denso. All other aspects of the system are working great. Clutches for these puppies are scarce & expensive, the cheapest I found was $277, dealer gets more than $400 for them (just the clutch alone!)

    They come apart easily, turn the ignition on & a/c on to lock the clutch & remove the center allen head screw, the fanbelt keeps the pulley from turning. Turn the key off & & take the belt off & wiggle the front plate off of the splined shaft. There is a large snap ring that keeps the pulley on at the center bearing. I had to modify a gear puller to get the pulley/bearing to pry off of the compressor nose, even after wetting it with P.B. Blaster.

    I didn't have to take it apart any further, the electro magnet stays put on the compressor. Once off, I chucked the pulley in the lathe & indicated the run out of the friction face within +/- .0005" & took a 0.005" skim-cut off the main friction surface. There were ridges ~0.040-0.050" higher than that from the flux escapement grooves in the front plate. The pulley's clutch friction surface is mild carbon steel and machines easily. The front plate friction surface is hardened but didn't show any appreciable wear & cleaned up nicely with a jitterbug. It only had one 0.040" shim in it so put it back together without it but then the gap was only ~.005" so machined a 0.010" shim for it from shim stock & that put the gap right at 0.016" so I called it good.

    Back together & engages sweet with a subtle "click" at 3500 rpm. Fixed the intermittant blower motor (sword) earlier this week, had the R-12 recharged last Spring, so should be set for several more seasons (fingers crossed).
    gale
    92 735i 5-spd, turbo project finally underway!


  2. #2
    Join Date
    Dec 2003
    Location
    baton rouge, loserana
    Posts
    6,922

    Default

    i wouldn't waste a near $300 clutch on a 12 year old seiko, it's probably not long for this world if your repair fails, i've seen quite a few lock up. new seiko's are hard to find but are still out there, the seltec/sanden conversion works well (if they have improved the belt tensioning system) and usually comes in cheeper even with the instalation kit, and if it ever pukes again the compressor is under 3 bills new
    all america wants is cold beer warm cat and a place to take a poop with a door on it

  3. #3
    Join Date
    Jan 2004
    Posts
    1,171

    Default

    Heck of a job Don.
    George...mine can't be too far from needing some work.

Similar Threads

  1. 540 A/c Compressor clutch
    By yaofeng in forum 5 Series BMW
    Replies: 6
    Last Post: 04-16-2008, 11:58 AM
  2. Replies: 5
    Last Post: 07-30-2007, 08:39 PM
  3. do i need a compressor or clutch or both???
    By tim s in forum 5 Series BMW
    Replies: 4
    Last Post: 06-09-2007, 03:08 PM
  4. a/c compressor clutch doesn't engage
    By motuman in forum 5 Series BMW
    Replies: 2
    Last Post: 03-17-2005, 05:32 PM
  5. Test drove a white '93 m5 this afternoon.
    By Martin in Bellevue in forum 5 Series BMW
    Replies: 1
    Last Post: 05-20-2004, 07:15 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •