Cold air on passenger side
Pulled the heater valve today and cleaned it. Checked to see if the solenoids were working properly, they were. Ran the car and still cold air on passenger side.....Disconnected the wires to the heater core and drove it again but still cold air on the passenger side. By theory if there is no power to the heater valve solenoid I should be getting hot air....correct? Why would I only be getting hot air on the drivers side and cold air on the passengers side?
I only have motor 1 and 3
I only have motor 1 and 3, then I have a cable controls where motor 2 should be.
http://i273.photobucket.com/albums/j...stepmotors.jpg
Can I pull the dash and open the top of the vent tubing and access the flap from there? Without having to pull the IHKA out?
http://i273.photobucket.com/albums/j...rventarrow.jpg
Quote:
Originally Posted by
shogun
These are the exterior air vents
Yes there is a motor on the drivers side (USA) and a cable that actuates the fresh air vent on the passenger side but this is fresh air vents that are on the firewall. The vents that I am talking about are in the interior of the car. Looking at all of the pictures it appears that if the dash is removed you should be able to remove the top of the IHKA without removing it. But then again I may be talking about the duct work on top of the IHKA. I think if the duct work is removed I should be able to get a closer look at the flap and perhaps repair it. What do I have to loose I still have to remove the dash anyway :) Now its off to find instruction on dash removal.
Quote:
Originally Posted by
shogun
Here is the arm through passenger floor vent
Here is a pic of the arm. Not the white arm but the black one behind it. I circled it with a yellow line. I will pull the existing and see if I can make one. Now I wish I had a mill.
http://i273.photobucket.com/albums/j...oe/flaparm.jpg
Quote:
Originally Posted by
shogun
I am afraid there are no single parts available from the dealer.
Only the housing center item # 3 complete
http://bmwfans.info/parts/catalog/E3..._conditioning/
Part number: 64 11 1 374 325 $ 236.50
options: get the upper part from a used one
or
make a aluminium bracket or from plastic, where you have the possibilities.
As a used one will probably also be brittle, I would try to make the brackets DIY.
Make as many pics as possible, and send them to me, to the link on my website, to Hairywithit, he will include that on the site. Will be good for future help.
And a short write up would also be good.
And when you have the parts made, new busines for you ;-)
many people will need them.
Plastic flap glued in place
Cleaned the shaft where the plastic flap broke off. Then spread some JB Weld along the broken edge of the flap, tried to make it a thin line just on the edge and the thickness of the plastic flap. Stayed away from the edge about 1/4" (see photo). Then I pushed the other flap closed in the other vent, this makes it easier to position the flap into place and gives it support on three of the four edges with the forth edge being the broken edge. Carefully place the broken flap into place making sure not to get glue anywhere except the break. Once the flap was in place I then smeared JBWeld along the broken seam. with a popsicle stick. Making sure not to get it too thick so it doesn't get on any other parts. That was about 2 hours ago, just went out to test it and it worked. Once it sets up over night I will apply JBWeld to the other side. I also spread JBWeld on the other flap, It has a couple of hair line cracks on it too. This is a tight area and my head was against the windshield and had to fight to get one eye into position to see down the hole :) Isn't the prettiest job with glue I have seen but if it works who cares ;)
http://i273.photobucket.com/albums/j.../flapglued.jpg
Quote:
Originally Posted by
Kibokojoe
Got the dash off in about 1 hour. Man what a job, it will probably take me more than a day to get it all back together. Looks like I will be able to repair the flaps without removing the IKHA but I need to know if I can get the parts. I have attached a picture of both flaps.
http://i273.photobucket.com/albums/j.../flapmetal.jpg
The metal flap "above" has plastic button which is lying next to the flap, broken in two pieces. The rest of the broken button can be seen through the floor vent, it is an arm. So I will need to get the arm. Wonder if it is available?
http://i273.photobucket.com/albums/j...lapplastic.jpg
The plastic flap "above" can be JB Welded back into place which I will do tonight Any suggestions before I proceed?????